MK23/SSX23 HPA M4 Magazine Adapter
Tested on STTI, TM, and older generation asg/ssx magazines.
Newer asg/ssx will not fit! (2022 onwards)
Fully Assembled package means we fit a gas magazine for you. I definitely recommend this, way easier!
These adapters are made to fit your existing MK23 magazines, it includes a Single Stack adapter, and a BB retention mechanism to reduce BB loss during mag changes.
Full support and warranty is offered for these products. This particular product was manufactured by ourselves and our UK manufacturing partner.
EPM1 magazines are highly recommended as they were used in the design process. Other brands may have issues with fitment.
Assembly
Installation is dead simple, you’ll need a quick grip vice such as this, a pin punch (2mm), basic screwdriver set and a hammer or mallet.
1) Punch out the bottom pins on the sides of the gas magazine to remove the gas block.
2) Punch out the pin holding in the feed lips, remove the feed lips and gas route
3) Insert the single stack adapter into the gas magazine
4) Fit the gasket to the Kross Airsoft Design HPA adapter (at this stage you can apply some silicone oil to the gasket to aid insertion )
5) Place the HPA Adapter into the magazine, and into the clamp. Tighten the clamp until the pin holes line up, and gently hammer them in.
6) Re install the gas route and feed lips. Hammer the feed lip pin back in
7) Go have fun!
PLEASE NOTE**
These do not work well with ARES magazines.
EPM1 are suited for the best results
Tested on STTI, TM, and older generation asg/ssx magazines.
Newer asg/ssx will not fit! (2022 onwards)
Fully Assembled package means we fit a gas magazine for you. I definitely recommend this, way easier!
These adapters are made to fit your existing MK23 magazines, it includes a Single Stack adapter, and a BB retention mechanism to reduce BB loss during mag changes.
Full support and warranty is offered for these products. This particular product was manufactured by ourselves and our UK manufacturing partner.
EPM1 magazines are highly recommended as they were used in the design process. Other brands may have issues with fitment.
Assembly
Installation is dead simple, you’ll need a quick grip vice such as this, a pin punch (2mm), basic screwdriver set and a hammer or mallet.
1) Punch out the bottom pins on the sides of the gas magazine to remove the gas block.
2) Punch out the pin holding in the feed lips, remove the feed lips and gas route
3) Insert the single stack adapter into the gas magazine
4) Fit the gasket to the Kross Airsoft Design HPA adapter (at this stage you can apply some silicone oil to the gasket to aid insertion )
5) Place the HPA Adapter into the magazine, and into the clamp. Tighten the clamp until the pin holes line up, and gently hammer them in.
6) Re install the gas route and feed lips. Hammer the feed lip pin back in
7) Go have fun!
PLEASE NOTE**
These do not work well with ARES magazines.
EPM1 are suited for the best results
Tested on STTI, TM, and older generation asg/ssx magazines.
Newer asg/ssx will not fit! (2022 onwards)
Fully Assembled package means we fit a gas magazine for you. I definitely recommend this, way easier!
These adapters are made to fit your existing MK23 magazines, it includes a Single Stack adapter, and a BB retention mechanism to reduce BB loss during mag changes.
Full support and warranty is offered for these products. This particular product was manufactured by ourselves and our UK manufacturing partner.
EPM1 magazines are highly recommended as they were used in the design process. Other brands may have issues with fitment.
Assembly
Installation is dead simple, you’ll need a quick grip vice such as this, a pin punch (2mm), basic screwdriver set and a hammer or mallet.
1) Punch out the bottom pins on the sides of the gas magazine to remove the gas block.
2) Punch out the pin holding in the feed lips, remove the feed lips and gas route
3) Insert the single stack adapter into the gas magazine
4) Fit the gasket to the Kross Airsoft Design HPA adapter (at this stage you can apply some silicone oil to the gasket to aid insertion )
5) Place the HPA Adapter into the magazine, and into the clamp. Tighten the clamp until the pin holes line up, and gently hammer them in.
6) Re install the gas route and feed lips. Hammer the feed lip pin back in
7) Go have fun!
PLEASE NOTE**
These do not work well with ARES magazines.
EPM1 are suited for the best results
