MK23/SSX23 HPA MP5 Magazine Adapter
Tested on ASG, STI, SSX23 and TM magazines
For best results, we recommend using cyma metal mid cap magazines.
Others may be slightly off spec and cause feeding issues.
Fully Assembled package means we fit a gas magazine for you. I definitely recommend this, way easier!
These adapters are made to fit your existing gas magazines, a Single Stack adapter and a BB retention mechanism to reduce BB loss during mag changes.
Full support and warranty is offered for these products. This particular product was manufactured by ourselves and our UK manufacturing partner.
Assembly
Installation is dead simple, you’ll need a quick grip vice such as this, a pin punch (2mm), basic screwdriver set and a hammer or mallet.
1) Remove the upper shell from the drum magazine by unscrewing the screws on the sides of the MP5 mag section, and pulling it apart
2) Punch out the pins from the drum magazine to remove the MP5 section entirely
3) Punch out the bottom pins on the sides of the gas magazine to remove the gas block.
4) Punch out the pin holding in the feed lips, remove the feed lips and gas route
5) Insert the single stack adapter into the gas magazine
6) Fit the gasket to the Kross Airsoft Design HPA adapter (at this stage you can apply some silicone oil to the gasket to aid insertion )
7) Place the HPA Adapter into the magazine, and into the clamp. Tighten the clamp until the pin holes line up, and gently hammer them in.
8) Re install the gas route and feed lips. Hammer the feed lip pin back in
9) Go have fun!
Tested on ASG, STI, SSX23 and TM magazines
For best results, we recommend using cyma metal mid cap magazines.
Others may be slightly off spec and cause feeding issues.
Fully Assembled package means we fit a gas magazine for you. I definitely recommend this, way easier!
These adapters are made to fit your existing gas magazines, a Single Stack adapter and a BB retention mechanism to reduce BB loss during mag changes.
Full support and warranty is offered for these products. This particular product was manufactured by ourselves and our UK manufacturing partner.
Assembly
Installation is dead simple, you’ll need a quick grip vice such as this, a pin punch (2mm), basic screwdriver set and a hammer or mallet.
1) Remove the upper shell from the drum magazine by unscrewing the screws on the sides of the MP5 mag section, and pulling it apart
2) Punch out the pins from the drum magazine to remove the MP5 section entirely
3) Punch out the bottom pins on the sides of the gas magazine to remove the gas block.
4) Punch out the pin holding in the feed lips, remove the feed lips and gas route
5) Insert the single stack adapter into the gas magazine
6) Fit the gasket to the Kross Airsoft Design HPA adapter (at this stage you can apply some silicone oil to the gasket to aid insertion )
7) Place the HPA Adapter into the magazine, and into the clamp. Tighten the clamp until the pin holes line up, and gently hammer them in.
8) Re install the gas route and feed lips. Hammer the feed lip pin back in
9) Go have fun!
Tested on ASG, STI, SSX23 and TM magazines
For best results, we recommend using cyma metal mid cap magazines.
Others may be slightly off spec and cause feeding issues.
Fully Assembled package means we fit a gas magazine for you. I definitely recommend this, way easier!
These adapters are made to fit your existing gas magazines, a Single Stack adapter and a BB retention mechanism to reduce BB loss during mag changes.
Full support and warranty is offered for these products. This particular product was manufactured by ourselves and our UK manufacturing partner.
Assembly
Installation is dead simple, you’ll need a quick grip vice such as this, a pin punch (2mm), basic screwdriver set and a hammer or mallet.
1) Remove the upper shell from the drum magazine by unscrewing the screws on the sides of the MP5 mag section, and pulling it apart
2) Punch out the pins from the drum magazine to remove the MP5 section entirely
3) Punch out the bottom pins on the sides of the gas magazine to remove the gas block.
4) Punch out the pin holding in the feed lips, remove the feed lips and gas route
5) Insert the single stack adapter into the gas magazine
6) Fit the gasket to the Kross Airsoft Design HPA adapter (at this stage you can apply some silicone oil to the gasket to aid insertion )
7) Place the HPA Adapter into the magazine, and into the clamp. Tighten the clamp until the pin holes line up, and gently hammer them in.
8) Re install the gas route and feed lips. Hammer the feed lip pin back in
9) Go have fun!
